Electrical Ground Fault Detection

Identification of electronic ground faults, shorts and opens: Utilizing Multi Meters, Electronic Transmitter and Receiver with A-frame to identify the precise location of electronic ground faults.

Electrical Fault Detection Electrical Fault DetectionElectrical Fault Detection

Buried cables do occasionally fail, for a variety of reasons and in many different ways. Lightening strikes, overloads or surges, installation problems, shovel and rodent damage are some of the common causes of damage that can lead to cable failure. Any discontinuity in the cable jacket which allows moisture in over time corrodes the conductors. Cables fail either open circuit, short circuit or somewhere in between, to earth and/or to another conductor in the cable. The type of fault should be determined as different faults require different approaches. A persistent fault to earth (a ground fault) is usually most accurately and most easily found with an A-frame. Open and short circuits are best found with a TDR, and a ‘flashing’ fault that only happens at high voltages usually requires a high voltage surge generator or ‘thumper’. Most transmitters in a fault finding system will have some way to indicate if there is a path to ground such as an ammeter or ohmmeter and some have both. If there is a path to earth, the a-frame is still one of the most popular and most recommended methods when the conductor is not enclosed in duct.

We can build on the methods of basic locating to detect persistent earth faults. We showed that cable locating is achieved by creating an alternating current (AC) on a cable and tracing the resulting AC electromagnetic (EM) field with a tuned receiver. A-frame systems differ in that in addition to the locate signal, we add a pulsed DC current (for ground fault locating) to the cable under test (CUT). The use of DC allows the detection of current direction and will lead the user towards a fault. Where there is contact with the earth, this current will flow out of the CUT at the fault and back to the ground stake of the transmitter. The current will be concentrated near the fault(s) and the ground stake but from those points will travel very wide and deep in search of the path of least resistance. Current through a resistance makes a voltage. The flow of the pulsed DC through the impedance of the earth will create a slight DC voltage and that is how we find faults. The addition of an A-frame to a locator basically turns the locator into a very sensitive voltmeter and following the pulsing DC through the earth with the A-frame gives a direction to and magnitude of the fault(s).

Because we are following the path of current through the earth, cables in duct cause us problems. Even if we have fault find signal flow, it doesn’t necessarily lead us to the fault. If the cable problem happens to be at the point of duct damage, we may have sufficient current flow through the earth from that location. Quite possible though is that there is moisture inside the duct and we are getting some current flow through that path as well, limiting our signal that leads us to the fault. If the cable problem is entirely within a good duct (such as happens when a jacket gets skinned while pulling it into the duct) all of our current flow can be inside the duct until a path to ground is reached, (such as at a defective duct joint) and we can’t find the fault. At best we can find where the moisture inside the duct is coming into contact with the earth such as at a bad joint.

Proper set up and use of an A-frame system requires that we prevent the fault locate current from getting to earth anywhere other than at the fault(s). This insures there is a maximum amount of signal to follow and it will lead us to the right position. As such, all other paths to ground, including neutrals and ground wires, have to be disconnected. This may require that power cables be taken completely out of service before testing for faults.

Use of a good earth ground is even more important when fault finding than it is with regular cable locating. An extra spool of ground wire with a large clip on the end is a valuable tool, allowing the use of distant, independent ground stakes. Stop signs, insulated anchors and existing but isolated ground stakes will often improve the performance of locate equipment. The practical limits of fault detection are around 0.5-2 M W of DC resistance depending on ground conditions. Since the A-frame is measuring voltage, it needs to have an electrical contact with the earth under it. Concrete, asphalt, dry or sandy soil are all high resistance paths to ground and can limit the voltage we can detect through the ground. Sometimes, wetting down the ground and even the pavement in the path of the target conductor will assist fault detection. Better yet, if there is access to unpaved ground running parallel to the target conductor, the Aframe may be used even if it is several meters off to one side.

After we have determined it is an earth fault and there is sufficiently low resistance to detect its position, we can start walking the path of the cable with the a-frame. There are two indications on most a-frame systems; signal strength and fault direction. The signal strength is best shown as a logarithmic value as there is a huge range of signal that can be detected. Close to the ground stake where there is a concentration of current, the receiver should indicate a large fault magnitude. It is a good idea to remember this value as a ‘reference number’. The value of the detected current (reference number) should be indicated at the fault location as well. Most manufacturers recommend that the A-frame be placed in the ground approximately the same distance away from the ground stake (in the direction opposite of the actual cable path) as the cable is deep, to get this initial fault magnitude reference.

Between the fault and transmitter the magnitude will drop, often substantially, as the current has spread out so far as thus become ‘diluted’. The behavior of the arrows may also change. Near the fault and the ground stake they will exhibit a good hard ‘lock’ on the fault direction but in the middle of the cable span, the weaker signal can result in fluctuations or no direction indication. The proper technique is to keep walking through the weak area and as we approach the fault, the signal will increase and normal operation will resume.

A fault is detected when two things happen; the signal strength increases due to the increased concentration of current as we approach the fault and the arrows suddenly reverse as we cross over the fault. Turning the a-frame 90 degrees and crossing the cable path will add more accuracy to the fault location. A final test of the fault location is to perform a ‘pothole’ or circle of the fault. Leave the front leg of the a-frame in the ground, directly over where the fault is believed to be and circle that point, placing the back leg in the ground in several points on the circle. If all signal indications point towards the stationary leg, we have found the best location. If the number in the receiver at this location does not reflect the reference number you saw back at the transmitter’s ground stake, you have an indication there may be more faults on this cable (or the cable depth is different than you expected).

If possible, excavate the fault, fix it or at least remove its contact with the earth and retest the cable with the ohmmeter function. Removing all contact includes drying the outside of the cable to prevent a current path through the moisture. If the cable now tests good, we can be confident there are no other faults on the cable.

Unjacketed concentric neutrals can pose a problem as our fault location current sometimes finds the neutral an easier path back to the area of the ground stake than the earth. This effect can be minimized by placing the ground stake as far away from the cable as possible and using a very good (low resistance) ground.

The A-frame is the most accurate but not necessarily the fastest tool to use as the operator has to walk the length of the cable from the transmitter to the ground fault. Often an earth fault has let in water and the conductors have also corroded open or short circuit. Using a Time Domain Reflectometer to estimate the rough location of a fault prior to the A-frame to find the exact point will often give the most efficient use of technicians’ time.

For more information and details on how to put CNI Locates electrical fault detection to work, call (877) 826-1177

Request a Free Estimate